Caterpillar D7E WH (Tier 4 Interim/Stage IIIB) Crawler Tractor
Dimensions
Bulldozer
Ground Clearance
49.8in
Blade Capacity - Sae J1265*
16.11yd3
Digging Depth
25.4in
Height
4.41ft in
Maximum Tilt
30.9in
Note (1)
*Capacities calculated with a trash rack installed.
Note (2)
**Weight includes cylinder mounting, lift cylinder and lines, blade, push arms, trunnions, and cylinder lines (Tilt).
Weight**
8492lb
Blade
7S LGP
Width - Over End Bits
14.91ft in
Specifications
Engine
Displacement
567cu in
Bore
4.5in
Stroke
5.9in
Net Power - Iso 9249
235hp
Net Power - Sae J1349
235hp
Gross Power - Sae J1995
259hp
Engine Model
Cat C9.3 ACERT
Flywheel Power
235hp
Gross Power - Iso 14396
256hp
Net Power - Iso 9249 (Din)
238hp
Global Emissions
U.S. EPA Tier 4 Interim/EU Stage IIIB/Japan MLIT Step 4
Gross Power - Iso 14396 (Din)
260hp
Drive Train
Drive Train Type
Electric Drive
Ac Compressor Nominal Input Voltage
320 V
Ac Compressor Maximum Input Current
12 A
Electric Water Pump System Nominal Input Voltage
320 V
Electric Water Pump System Nominal Input Current
5 A
Ac Generator And Propulsion Module Voltage
480 V
Operational
Operating Weight
68600lb
Weights
Operating Weight - Lgp Wha
68600lb
Shipping Weight - Lgp Wha
58900lb
Service Refill Capacities
Cooling System
22.5gal
Fuel Tank
108gal
Engine Crankcase
8gal
Power Train
16gal
Pivot Shaft Compartment
1.8gal
Final Drive - Each - Lgp
9gal
Standards
Brakes
ISO 10265 2008
Rops/Fops
ROPS meets criteria ISO 3471:1994, 2008; FOPS meets ISO 3449:1992, 2005 Level II
Cab
ANSI/SAE J1166 OCT 98
Hydraulic Controls - Main Relief Valve
Pressure Setting - Steering
4000 psi
Hydraulic Controls - Maximum Operating Pressure
Bulldozer
4000 psi
Tilt Cylinder
4000 psi
Ripper - Pitch
4000 psi
Ripper - Lift
4000 psi
Steering
5950 psi
Hydraulic Controls - Pump
Lift Cylinder Flow
42 gal/min
Ripper Cylinder Flow
42 gal/min
Pump Output - Steering
82.4 gal/min
Pump Output - Implement
52.8 gal/min
Pump Type
Piston, Variable Displacement
Tilt Cylinder Flow - Head End Flow
24.6 gal/min
Tilt Cylinder Flow - Rod End Flow
17.4 gal/min
Rippers
Maximum Penetration Force
19639lb
Pry-Out Force
52695lb
Overall Beam Width
82.2in
Beam Cross Section
14in
Weight - With One Shank
3572lb
Weight - Each Additional Shank
330lb
Ramp Angle
26degrees
Pocket Spacing
35.4in
Shank Gauge
70.9in
Shank Section
72 mm 228 mm (2.8 in 9.0 in)
Rippers Type
Multi-Shank
Number Of Pockets
3
Maximum Clearance Raised - Under Tip, Pinned In Bottom Hole
23.1in
Maximum Penetration
25.6in
Winches
Weight*
3350lb
Drum Capacity - 24 Mm (1 In)
203ft in
Drum Capacity - 29 Mm (1.13 In)
185ft in
Oil Capacity
3.2gal
Winch Model
PA90
Increased Tractor Length - Lgp
93.9in
Drum Diameter
12.5in
Winch Drive
Hydraulic
Maximum Bare Drum - Line Pull
90000lb
Maximum Full Drum - Line Pull
57000lb
Maximum Bare Drum - Line Speed
70 ft/min
Maximum Full Drum - Line Speed
116 ft/min
Note
*Basic winch weight, mounting arrangement, hydraulic and electrical system weight.
