Caterpillar 986K Block Handler Arrangement Wheel Loader
Specifications
Engine
Net Power
373hp
Displacement
927cu in
Torque Rise
16%
Bore
5.4in
Stroke
6.8in
Emissions
U.S. EPA Tier 4 Final/EU StageIV, or China Nonroad Stage III and Brazil MAR-1 and equivalent to U.S.Tier 3 and EU Stage IIIA
Engine Model
Cat C15 ACERT
Gross Power - Iso 14396
449hp
Peak Torque - 1,200 Rpm - Sae J1995
1778lb ft
Peak Power Speed - 1,600 Rpm - Sae J1995 (Din)
462hp
Peak Power Speed - 1,600 Rpm - Iso 14396
449hp
Peak Power Speed - 1,600 Rpm - Iso 14396 (Din)
455hp
Rated Speed - 2,000 Rpm - Eec 80/1269
373hp
Rated Speed - 2,000 Rpm - Eec 80/1269 (Din)
378hp
Rated Speed - 2,000 Rpm - Iso 9249
373hp
Rated Speed - 2,000 Rpm - Iso 9249 (Din)
378hp
Rated Speed - 2,000 Rpm - Sae J1349
373hp
Rated Speed - 2,000 Rpm - Sae J1349 (Din)
378hp
Peak Power Speed - 1,600 Rpm - Sae J1995
456hp
Operational
Operating Weight
116688lb
Transmission
Transmission Type
Cat Planetary Power Shift
Forward - 1
5mph
Forward - 2
8mph
Reverse - 1
5mph
Reverse - 2
8mph
Direct Drive - Forward 3
14mph
Direct Drive - Reverse 3
16mph
Direct Drive - Forward 4
24mph
Direct Drive - Forward 2
8mph
Direct Drive - Reverse 2
9mph
Direct Drive - Reverse 4
25.4mph
Buckets
Bucket Capacities
5.4 m (7 yd)
Axles
Front
Fixed
Rear
Trunnion
Oscillation Angle
12.5 degrees
Oscillation Angle - Chain Arrangement
8.5 degrees
Brakes
Brakes
ISO 3450:2011
Service Refill Capacities
Fuel Tank
116gal
Crankcase
9gal
Transmission
20gal
Hydraulic System Factory Fill
87gal
Hydraulic System - Tank Only
34gal
Cooling Systems
26gal
Diesel Exhaust Fluid Tank (For Tier 4 Final/Stage Iv Only)
6gal
Axle Oil - Differentials And Final Drives - Front
49gal
Axle Oil - Differentials And Final Drives - Rear
45gal
Hydraulic Cycle Times
Raise
8.5 s
Dump
3 s
Lower Float Down
4.3 s
Rack Back
4.5 s
Lower
4.9 s
Total Hydraulic Cycle Time
15.8 s
Hydraulic System - Lift/Tilt
Lift/Tilt System - Circuit
Load Sense
Lift/Tilt System - Pump
2 110 cc variable displacement
Relief Valve Setting - Lift/Tilt
4050 psi
Maximum Flow At 2,165 Rpm
123 gal/min
Tilt Cylinder - Stroke
22.4in
Lift Cylinder - Bore
7.5in
Lift Cylinder - Stroke
45in
Tilt Cylinder - Bore
6.7in
Hydraulic System - Steering
Iso 5010:2007 - Steering System - Circuit
Load Sense
Iso 5010:2007 - Steering System - Pump
Piston, variable displacement
Iso 5010:2007 - Total Steering Angle
70 degrees
Iso 5010:2007 - Maximum Flow At 1,400 Rpm
52 gal/min
Iso 5010:2007 - Steering Cutoff Pressure
4000 psi
Air Conditioning System
Air Conditioning
The air conditioning system on this machine contains the fluorinated greenhouse gas refrigerant R134a (Global Warming Potential = 1430). The system contains 1.8 kg of refrigerant which has a CO2 equivalent of 2.574 metric tonnes.
Dimensions (Approximate) - Quick Coupler And 6.1 M³ (8.0 Yd³) Bucket
Ground To Top Of Rops
13.5ft in
Ground To Top Of Exhaust Stacks
13.3ft in
Ground To Top Of Hood
10.7ft in
Ground To Center Of Rear Axle
3.2ft in
Ground To Fuel Tank Clearance
2.3ft in
Ground To Lower Hitch Clearance
1.5ft in
Reach At Maximum Lift
8ft in
Clearance At Maximum Lift
10.7ft in
B-Pin Height At Maximum Lift
15ft in
Maximum Overall Height, Bucket Raised
20.9ft in
Rear Axle Center Line To Bumper
10.3ft in
Wheel Base
12.5ft in
Maximum Overall Length
35ft in
Front Axle Centerline To Bucket Tip
12.2ft in
Dimensions (Approximate) - Quick Coupler And Fork
Ground To Top Of Rops
13.5ft in
Ground To Top Of Exhaust Stacks
13.3ft in
Ground To Top Of Hood
10.7ft in
Ground To Center Of Rear Axle
3.2ft in
Ground To Fuel Tank Clearance
2.3ft in
Ground To Lower Hitch Clearance
1.5ft in
B-Pin Height At Maximum Lift
15ft in
Rear Axle Center Line To Bumper
10.3ft in
Wheel Base
12.5ft in
Maximum Overall Length
35.4ft in
Front Axle Centerline To Bucket Tip
12.6ft in
Operator'S Cab
Rops/Fops
ROPS/FOPS meet ISO 3471:2008 (ROPS) and ISO 3449:2005 Level II (FOPS)
Sound Performance - Standard
Note
<ul><li>The operator sound pressure level was measured according to the test procedures and conditions specified in ISO 6396:2008. The measurement was conducted at 70 percent of the maximum engine cooling fan speed.</li><li>Hearing protection may be needed when the machine is operated with a cab that is not properly maintained or when the doors or windows are open for extended periods or in a noisy environment.</li><li>The machine sound power level was measured according to the test procedures and conditions specified in ISO 6395:2008. The measurement was conducted at 70 percent of the maximum engine cooling fan speed.</li></ul>
Operator Sound Level (Iso 6396)
72 dB(A)
Machine Sound Level (Iso 6395)
112 dB(A)
Sound Performance - Suppression
Note
<ul><li>The operator sound pressure level was measured according to the test procedures and conditions specified in ISO 6396:2008. The measurement was conducted at 70 percent of the maximum engine cooling fan speed.</li><li>Hearing protection may be needed when the machine is operated with a cab that is not properly maintained or when the doors or windows are open for extended periods or in a noisy environment.</li><li>The machine sound power level was measured according to the test procedures and conditions specified in ISO 6395:2008. The measurement was conducted at 70 percent of the maximum engine cooling fan speed.</li></ul>
Operator Sound Level (Iso 6396)
72 dB(A)
Machine Sound Level (Iso 6395)
110 dB(A)
